Видео

Is this steve voice?

Help please. When I try and do this using my transmitter as my tx has the same function my transmitters stops transmitting, the RSSI drops below 15 and does not calibrate. I have moved my tx away from the rx and have even moved locations but to no avail. However when i am not calibrating my rx my tx works perfectly well and the RSSI reading over 100. It appears that this only happens when I am in the calibration mode. Any idea why this is?

Too complicated...

Thank you. But where can I buy a battery for my new Taranis X9D Plus 2019 as I can't seem to find one? Thanks.

saya telah membeli X10S, karena tidak terbiasa dengan fros saya ganti ke EdgeTX untuk dipasang module ELRS tanpa masalah. namun module multi JP4in1 tidak bisa digunakan di remot ini. 😢

are you the official channel for FrSKY Company?

It is universal? Can be pair with any drone?

For those of you complaining that your receivers will no longer work after this internal firmware update, it's because you MUST also update the firmware in every receiver that you plan to use also.

What range can this fly out to please ?

Can you guys make more FPV radios? And maybe with ExpressLRS

What is the output voltage of these TD R receivers and is it changeable? It doesn’t list this in the manual or on your site

Please do a video on the TD SR18 stability programming. Im looking for a very flexable Gyro, where i can turn some channels off in different flight modes, as well as viable gains on orher channels. Is this avle to be done. Very little information out there

The Airlink S is mostly useless especially for the new ArcherPlus receivers.. You can neither flash nor configure. Here's my experience actually getting these new receivers up and running.

nice vid, im on mode 4 ,the other tx on mode 3,when using bluetooth the slave radio is using my mode 4 , as he flys mode 3 he cant fly is this compatable , can you use 1 mode in one tx and another mode in another tx ????? cheers

I see that the FRSKY TD R18 does give the voltage of each battery (RxBatt1; RxBatt2). Does the FRSKY TD SR18 model (with stabilizer) also give the voltage of each battery (RxBatt1; RxBatt2)??? . Thanks

What is same as for Receiver R9Stab OTA 915Mhz? For calibration and set to Delta Wing (Elevon Stabilised)

So I couldn't bind to the dongle with Frsky X20. My x20 is updated including module. Anyway's my solution is to install firmware 2.1.0-1 to dongle. I solder a servo extension to the dongle and inserted to the top of where the charger jack is. Was easy then I went to my radio selected the firmware and flash to external device and blam i was able to bind to it :) To bad I had to do all that work but was really simple

Can I use this bluetooth to transmit telemetry to smartphone/pc on x lite s?

i love fr sky so much

can you remove the hand rest on the sides? Other than that looks great.

i can't find the sd card folder

Thank you, I did successfully flash with this procedure.

I never get a blue light after holding button down for 4 seconds

Does it work for the older legacy radios?

what a complete waste of time and money.

Wow! A TD R18 receiver has moved to the top of my shopping list.

Works on Android via BT but not on a PC. It does not connect at all. CRAP.

Why Name the Button download when its uplosding the Firmware???????

…mucho costo dinare…

I have the 5405 servo. What is the dead band? and can it be adj? I noticed when you move the stick slow and a little the servo doesn't move and other servos I have will move side by side

Hey, just stopping by to say that if someone is using Taranis X9D with the XSR SIM dongle, they need to update their Taranis firmware to at least the same version as the dongle. In my case LBT 2.1.0. It would not bind otherwise.

Hi, I have an XJT transmitter module but don't have a transmitter. I use the XJT module in my JR XP9303 radio. Can I use the STK took to flash the XJT with the latest firmware? Thanks

Hola , tengo esta emisora Taranis Qx7 desde 2018 , al dia de hoy nunca la pude usar porque no encontre video ni a nadie que me diga o enseñe como ponerla en modo helicoptero , podrias ayudarme con algun video asi la puedo usar con mis helicopteros electricos KDS450 ? gracias .

Como configurar rb40 con el modulo sport airlink vía Bluetooth??lo intento y en el tlf ne aparece que no está conectado a Bluetooth

is there an updated video? the freelink.exe on the website is different from the one in this video ( and doesn't work )

Can you explain how to set up the TRAINER function. Maybe a new short video.

The red switch panel in the video is not included, it is used to power on/off the power supply just like disconnecting a battery. There are different types of external switch accessories for the TDR18 receiver like an audio-jack-type pin switch (bit.ly/3KOR10t ) and NFC switch panel (bit.ly/3xk7Qv5 ).

This video is out of date and will not help you install the STK tool, RC Groups will help

This video is out of date and useless please update the video!!!!

So, what is the advantage to having these servos vrs a normal digital servo or even pwm servo?

…👍😜

…👍😜

How many watts @ 24v?

Doesn't seem to offer any advantages over a TS80/TS100

Nice portable iron 😎

I have bought 2 TD receivers and the 900 mhz telemetry makes my servos jitter like crazy. They are multiplex, Hitech and emax servos. I have tried every position of antennas. The only thing that makes the jitter go away is to wrap the 900 mhz antenna in aluminum foil or turn telemetry off altogether: clearly not viable. I had to return the rx

Nice video. If I may ask How do you do firmware upgrade of the RB 10 itself ?

Fake… dozen work yet